Jukskei Toerusting | Equipment

1. Skeie mag alleenlik van hout, rubber, rubber-komposisie of sintetiese materiaal, of deur ‘n samestelling, wat deur die IJF goedgekeur is, vervaardig word.  Tot op Nasionalevlak mag skeie wat deur Jukskei SA goedgekeur is gebruik word
2. Die totale lengte van ‘n skei (handvatsel ingesluit) is tussen 300mm minimum en 460mm maksimum.
3. Die romp van die skei moet silindries wees met ‘n deursnee van tussen 50 mm minimum en 75mm maksimum.
4. Die maksimum gewig van ‘n skei is 1.8kg

Skeys

1. Skeys may only be made from wood, rubber, rubber composite, synthetic materials or a combination there-of, as approved by the IJF.  Up to National level skeys may be used that are approved by Jukskei SA.
2. The total length of a skei (including the handle) must be between a minimum of 300mm and a maximum of 460mm.
3. The body of the skei must be cylindrical with a diameter between 50mm minimum and 75mm maximum.
4. The maximum weight of a skei is 1.8kg.

1. Penne mag uitsluitlik van hout of deur IJF goedgekeurde sintetiese materiaal vervaardig word.
2. Die lengte van ‘n pen is 495mm (minimum) tot 500mm (maksimum).
3. Die deursnee van ‘n pen is 27mm (minimum) tot 32mm (maksimum).
4. Die romp van die pen moet silindries wees.
5. Die een end van ‘n pen moet oor ‘n afstand van 50mm tot ‘n 5mm punt taps wees.  Die ander end (kop van die pen) moet plat wees en nie rond nie.  (Sien skets van pen)
6. ‘n Windmerk van 18mm (minimum) tot 20mm (maksimum) breed moet op die pen aangebring wees beginnende vanaf die bokant van die 50mm taps gedeelte
7. Die punt van die pen mag met ‘n skroef versterk word.  Die vorm van die punt mag egter nie geaffekteer word nie.  Die dikte van die kop van die skoef is ingesluit by die 50mm taps gedeelte.

Pegs
1. Pegs may only be made of wood or synthetic material approved by the IJA.
2. The length of a peg is a minimum of 495mm and a maximum of 500mm.
3. The diameter is a minimum of 27mm and a maximum of 32mm.
4. The body of the peg must be cylindrical.
5. One end of a peg must be tapered from 50mm to a point 5mm in diameter.  The other end must be flat and must not be rounded.  (See sketch of a peg.)
6. A wind mark of minimum 18mm and a maximum of 20mm wide must be marked on the peg, starting at the top of the 50mm tapered end.
7. The point of the peg may be strengthened with a screw.  The shape of the tapered point may not be influenced.  The thickness of the screw’s head is included in the 50mm tapered end.

1. Vir meetdoeleindes is ‘n standaard passer van 460mm noodsaaklik

Caliper

1. For measuring purposes it is essential to have a caliper with an a maximum measuring ability of 460mm.

1. Die dwarslyn mag slegs van lyn of tou wees.
2. Die dikte van die dwarslyn mag nie twee (2) millimeter oorskry nie.
3. Die dwarslyn word aan die eenkant permanent vasgeheg.
4. Aan die ander end van die dwarslyn moet ‘n lus, hakie of ring wees om oor die teenoorgestelde skroef/ spyker of soortgelyke voorwerp te haak sodat die dwarslyn styf gespan kan word.
5. ‘n Knoop wat die presiese middelpunt van die breedte van die sandput aandui, moet in die dwarslyn aangebring word.

String

1. Only line or string may be used.
2. Thickness must not exceed two (2) mm.
3. Must be permanently secured to one side.
4. The other end must have a loop, hook or ring which can be hooked over the opposite screw / nail or similar object in the framework allowing the string to be drawn tightly.
5. A knot that indicates the exact centre of the width of the sandpit must be tied in the string.